How to Mount a Ring Video Doorbell on Any Wall

Set up your Ring doorbell approximately 48 inches (1.2 m) from the ground, and if the camera faces the wrong direction, attach a wedge or corner kit; when mounting on brick or stucco, use masonry anchors. Put the kit in first, then install the doorbell.

Your model and your wall determine the correct anchors and kit. Before handling a wired doorbell, shut off its power at the breaker, which is the switch in your home’s electrical panel. For app setup and wiring, see installing a Ring Video Doorbell the safe way.

Which wedge and corner kit fits your doorbell

A wedge kit angles the doorbell either up or down. A corner kit rotates it left or right, which is useful when the doorbell is mounted on a door frame or a wall facing the wrong direction. Ring offers both options, with the piece count in each box varying according to your model.

Doorbell kits are designed to work with particular generations of doorbells. Prior to purchasing, compare the compatibility list found on the kit’s packaging or listing with your specific model name, such as Ring Video Doorbell 2nd Gen or Wired Doorbell Pro. A kit designed for a different generation might not align with the screw holes on your doorbell.

1. Select a location roughly 48 inches (1.2 m) above the ground, beside the door, offering an unobstructed view of the porch and walkway.
2. Hold the doorbell vertical.
3. If you have a battery model that is already set up in the Ring app, ask a helper to hold it in place while you check the camera view on your phone. Determine if you require a tilt (wedge), a turn (corner), or both.
4. Determine your wall type: wood, brick, stucco or vinyl siding. Each of these is covered in Step 4.

1. Lay out the wedge or corner kit, its included screws and wall anchors, plus the mounting bracket that comes with the doorbell.
2. If you’re working with brick, concrete or stucco, you’ll also need a drill that has a 1/4 inch (6 mm) masonry bit. For brick, a hammer drill fitted with a carbide bit works best.
3. Have a pencil, a level and a screwdriver within reach.
4. For now, set aside the screws that came with your doorbell. Use the screws supplied with each part.

1. Locate your doorbell’s breaker. When the panel lacks labels, shut off the breaker you believe is correct, then press the old doorbell button. If the chime continues to sound, attempt another.
2. Keep the breaker off until your new doorbell is mounted and wired.
3. Omit this step if your doorbell is powered exclusively by its battery.

Position the kit (or the bracket, if no kit is used) against the wall, use the level to level it, and use the pencil to mark the screw holes. Next, adhere to the guidelines specific to your wall.

• Wood (door frame or trim): According to Ring, wood requires neither drilling nor anchors. The screws drive right in.
• Brick: Run a hammer drill with a carbide bit at low speed and make a 1/4 inch (6 mm) hole. Target the mortar joints, the gray lines between bricks, whenever possible. Because mortar is softer, the brick is less prone to cracking, and repairing a bad hole is simpler. Insert the included wall anchors into the holes.
• Traditional stucco (hard coat over wire mesh): Make 1/4 inch (6 mm) pilot holes, then use the included wall anchors. This is generally sufficient.
• EIFS stucco (a thin coat over foam): Foam might not hold the included anchors. If you are unsure which type you have, or you do not know the right anchors, check with a hardware store or a pro installer about which anchors and sealant work for your wall before drilling.
• Vinyl siding: You should avoid drilling through the siding to mount the doorbell. Mount the doorbell using a siding mount (an accessory sold separately). Start by measuring your panel to confirm the mount fits those dimensions, and then follow the instructions provided with the mount.
• No drilling allowed (renters): An adhesive mount is a no-drill choice. Verify that it’s compatible with your doorbell model and follow the instructions for your mount.

To distinguish EIFS from traditional stucco, check a concealed area, like low on the wall behind a bush. Knock on it and push hard using your thumb. Traditional stucco sounds hard and solid. EIFS sounds lighter and hollow, and it may give slightly. If a pilot hole reveals foam, you’re dealing with EIFS.

1. Stack the pieces you need. Use a maximum of one corner kit and one wedge kit, placing the wedge on top of the corner.
2. You can stack up to 15° of wedge and as much as 45° of corner on most models. The Wired Doorbell Pro and Video Doorbell Wired use a single 25° corner mount that cannot be stacked.
3. Secure the stack to the wall using the screws provided in the kit. Never substitute screws from a different box.
4. Use the level to confirm the stack rests evenly and stays steady.

Ring’s support article on wedge and corner kits (new tab) displays how the kits stack in order.

1. For a wired model, follow your doorbell’s instructions to connect the wires. The wiring steps are detailed in installing a Ring Video Doorbell the safe way.
2. Mount the doorbell on the bracket or the kit, then push it into place.
3. Use the screwdriver to drive in the security screw. This screw secures the doorbell to the bracket, making the doorbell harder to pull off the wall. Ring’s guide to the physical install of the 2nd Gen (new tab) illustrates its location.
4. If your model is wired, switch the breaker back on and wait until the light ring turns on.

1. Launch the Ring app and check the camera view from your doorbell. Frame the shot to capture the door, porch, and walkway, keeping the street mostly out of view.
2. Cross the yard on foot and head to the door. Verify that you receive a motion alert.
3. Should passing cars trigger alerts, either adjust the settings under “Motion Settings” › “Motion Zones” within the Ring app, or install a wedge or corner piece. Menu names can vary slightly depending on the model and app version.
4. Should the camera angle sit excessively high or low, you can insert or take out a wedge piece. If it aims too far left or right, swap the corner piece. With a wired model, shut off the breaker once more beforehand.

Frequently Asked Questions

How high should I mount a Ring doorbell?

Approximately 48 inches (1.2 m) off the ground is the typical mounting height. Should the camera aim excessively upward or downward, a wedge kit corrects the angle.

Can I mount a Ring doorbell on brick or stucco without cracking it?

Yes. Use a hammer drill equipped with a carbide masonry bit at slow speed, target mortar joints on brick, and use the wall anchors provided. With EIFS stucco (over foam), the included anchors might not hold, so check with a hardware store or professional installer about which anchors to use.

What is the difference between a wedge kit and a corner kit?

A wedge kit adjusts the doorbell vertically. A corner kit rotates it left or right. You can use one of each, placing the wedge above the corner.

Can I mount a Ring doorbell without drilling?

Yes. Adhesive mounts and vinyl-siding mounts require no drilling. Verify that the mount is designed for your doorbell model and follow its instructions.

Why does my Ring doorbell send too many motion alerts after mounting?

The camera is likely aimed at the street or a busy sidewalk. Use a corner kit to rotate it, or tweak the zones under “Motion Settings” in the Ring app. See Ring doorbell problems and fixes for other causes, or browse common Ring doorbell questions.

Written with AI assistance. Facts and sources are checked automatically before publication. How we work